2013-11-06 00:20 bzb has quit [Read error: Connection reset by peer]
2013-11-06 00:27 biot has quit [Ping timeout: 260 seconds]
2013-11-06 00:29 biot has joined #qi-hardware
2013-11-06 00:44 bzb has joined #qi-hardware
2013-11-06 01:20 bzb has quit [Remote host closed the connection]
2013-11-06 01:41 dos1 has quit [Ping timeout: 268 seconds]
2013-11-06 01:44 xiangfu has joined #qi-hardware
2013-11-06 02:58 xiangfu has quit [Ping timeout: 245 seconds]
2013-11-06 03:00 xiangfu has joined #qi-hardware
2013-11-06 03:11 xiangfu has quit [Ping timeout: 246 seconds]
2013-11-06 03:13 xiangfu has joined #qi-hardware
2013-11-06 03:52 unclouded has quit [Quit: Leaving]
2013-11-06 04:19 kanzure_ has joined #qi-hardware
2013-11-06 04:20 qi-bot8 has joined #qi-hardware
2013-11-06 04:23 panda|x201 has quit [*.net *.split]
2013-11-06 04:23 qi-bot has quit [*.net *.split]
2013-11-06 04:23 kanzure has quit [*.net *.split]
2013-11-06 04:23 qi-bot8 is now known as qi-bot
2013-11-06 04:30 panda|x201 has joined #qi-hardware
2013-11-06 05:30 panda|x201 has quit [Ping timeout: 246 seconds]
2013-11-06 06:19 Luke-Jr has quit [Read error: Connection reset by peer]
2013-11-06 06:19 Luke-Jr has joined #qi-hardware
2013-11-06 06:55 wolfspraul has joined #qi-hardware
2013-11-06 06:56 Luke-Jr has quit [Excess Flood]
2013-11-06 06:57 Luke-Jr has joined #qi-hardware
2013-11-06 08:24 jekhor has joined #qi-hardware
2013-11-06 08:31 xiangfu has quit [Remote host closed the connection]
2013-11-06 08:58 lekernel has joined #qi-hardware
2013-11-06 09:00 <apelete> Good morning
2013-11-06 09:02 <apelete> larsc: tried calling musb_pullup() from within the musb glue code but it didn't help detecting the endpoints, just like you said
2013-11-06 09:05 <apelete> so next step is to try to use ep_config_from_table() as you suggested.
2013-11-06 09:05 <apelete> don't know how it works yet, how to use it instead of relying on ep_config_from_hw()
2013-11-06 09:05 <apelete> will need to read some code to find out
2013-11-06 09:25 <larsc> I think you need to setup a musb_fifo_cfg array in your glue code
2013-11-06 09:25 <larsc> this seems to configure the size and the direction of each ep
2013-11-06 09:36 <larsc> or as a quick hack you could take the same approach as blackfin and overwrite musb_read_fifosize(), but that's nothing that will make it into upstream
2013-11-06 09:46 <apelete> larsc: ok, will try the musb_fifo_cfg array solution then, since going upstream was the initial goal of the glue code :)
2013-11-06 09:46 <apelete> thanks for the advice
2013-11-06 10:15 panda|x201 has joined #qi-hardware
2013-11-06 10:30 xiangfu has joined #qi-hardware
2013-11-06 11:05 wej has quit [Ping timeout: 260 seconds]
2013-11-06 11:08 wej has joined #qi-hardware
2013-11-06 11:22 dos1 has joined #qi-hardware
2013-11-06 12:05 jekhor has quit [Read error: Operation timed out]
2013-11-06 13:52 xiangfu has quit [Ping timeout: 272 seconds]
2013-11-06 13:58 xiangfu has joined #qi-hardware
2013-11-06 14:52 wej has quit [Ping timeout: 264 seconds]
2013-11-06 15:01 xiangfu has quit [Remote host closed the connection]
2013-11-06 15:46 pcercuei has joined #qi-hardware
2013-11-06 15:57 pcercuei has quit [Ping timeout: 245 seconds]
2013-11-06 17:17 wej has joined #qi-hardware
2013-11-06 17:25 rz2k has joined #qi-hardware
2013-11-06 17:57 panda|x201 has quit [Ping timeout: 265 seconds]
2013-11-06 18:07 porchao has joined #qi-hardware
2013-11-06 18:59 rz2k has quit []
2013-11-06 19:04 panda|x201 has joined #qi-hardware
2013-11-06 20:09 uwe__ has joined #qi-hardware
2013-11-06 20:09 uwe_ has quit [Ping timeout: 240 seconds]
2013-11-06 20:35 unclouded has joined #qi-hardware
2013-11-06 20:49 pcercuei has joined #qi-hardware
2013-11-06 21:33 kristianpaul has joined #qi-hardware
2013-11-06 22:10 lekernel has quit [Ping timeout: 260 seconds]
2013-11-06 22:23 lekernel has joined #qi-hardware
2013-11-06 23:13 lekernel has quit [Quit: Leaving]
2013-11-06 23:38 wolfspraul has quit [Quit: leaving]
2013-11-06 23:55 jekhor has joined #qi-hardware